do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
Support Brackets / Retainers / Braces
By OE Match
- Porsche 356 1950-55
- Porsche 356A 1955-59
Fits:
Porsche 356 / 356A 1950-1959
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
64450513100
The product you are viewing cross references to these numbers
- Porsche 356A 1955-59
Sold as a pair
Fits:
Porsche 356A - 1955 to 1958 USA cars only
We had these reproduced from the original U.S.-style bumper support tubes.
Over the years, these tubes often get bent from minor bumps or everyday driving mishaps.
These feature the O.E. "Adjusting Eye Hole," which is crucial since every car was hand-built and slightly different. This adjustment hole allows you to properly align your bumper with the necessary flexibility, just like the original design.
This is the front 155mm long bumper support tube for 1955-58 356A only.
Sold as a pair.
Diagram ref no 6
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
64450516100
The product you are viewing cross references to these numbers
- Porsche 356A 1955-59
Sold as a pair
Fits:
Porsche 356A - 1959 USA cars only
We had these reproduced from the original U.S.-style bumper support tubes.
Over the years, these tubes often get bent from minor bumps or everyday driving mishaps.
These feature the O.E. "Adjusting Eye Hole," which is crucial since every car was hand-built and slightly different. This adjustment hole allows you to properly align your bumper with the necessary flexibility, just like the original design.
This is the front 190mm long bumper support tube for (2/59) 1959 356A only.
Sold as a pair.
Diagram ref no 6
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
64450516101
The product you are viewing cross references to these numbers
- Porsche 356 1950-55
- Porsche 356A 1955-59
Sold as a pair
Fits:
Porsche 356 - 1950 to 1955 USA cars only
Porsche 356A - 1955 to 1959 USA cars only
We had these reproduced from the original U.S.-style bumper support tubes.
Over the years, these tubes often get bent from minor bumps or everyday driving mishaps.
These feature the O.E. "Adjusting Eye Hole," which is crucial since every car was hand-built and slightly different. This adjustment hole allows you to properly align your bumper with the necessary flexibility, just like the original design.
Sold as a pair.
Diagram ref no 10 and 11
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
644505261262
The product you are viewing cross references to these numbers
- Porsche 356 1950-55
- Porsche 356A 1955-59
This set is manufactured replacement kit designed for the front bumper mounting of Porsche 356 (mid 1952-55) and Porsche 356A (1955-59) vehicles. These brackets replicate the original geometry, drilling, and mounting hardware specification so your bumper aligns perfectly, sits securely, and retains classic appearance.
Fits:
Porsche 356 Mid 1952 - 1955
Porsche 356A 1955 - 1959
Diagram ref no 3, 4 and 5.
• Position on Vehicle: Front of vehicle — left and right side bumper bracket mounts connecting bumper to body/chassis.
• Applications: Ideal when original brackets are missing, bent, corroded or when restoring the vehicle’s exterior to original condition.
Properly aligned and securely mounted bumpers are essential for vehicle appearance, safety and panel fitment. Worn or distorted brackets can cause misaligned bumpers, poor gaps, vibrations or damage in minor impacts. Replacing with this kit restores precision mount geometry, improves the front end’s visual integrity and helps protect investment in your classic.
When and why to replace:
• Original bumper brackets are bent, damaged or corroded.
• Gaps around the bumper are uneven or the bumper is misaligned.
• During front-end restoration, repainting or bodywork where the bumper needs removal.
• When authenticity and correct fitment are required for a classic Porsche build.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
64450513100
The product you are viewing cross references to these numbers
- Porsche 356B 1959-63
- Porsche 356C 1963-65
This 4-piece front bumper bracket set precisely replicates the factory inner/outer mounting arms that secure the front bumper to the chassis horns on Porsche 356 B/C models. Press-formed from the correct-thickness steel with OE-style bends and slotted mounting holes for alignment, each bracket restores proper bumper position, panel gap, and contour to the front fenders. A corrosion-resistant finish helps resist rust and road grime for long service life.
Fits:
Porsche 356B 1960 - 1963
Porsche 356C 1964 - 1965
Diagram ref no 3 and 4
Includes:
2 × 64450513105 – Front bumper outer brackets (LH/RH)
2 × 64450513305 – Front bumper inner brackets (LH/RH)
Why to replace:
Front bumper brackets often suffer from rust, deformation, or impact damage over time. Corroded or bent brackets can cause misalignment, sagging corners, or uneven body gaps, affecting both appearance and structural support. Replacing them ensures the bumper sits correctly and maintains the classic Porsche contour and integrity.
When to replace:
Replacement is recommended during front-end restorations, bumper repainting, or after minor collisions. It’s also wise to install new brackets if you notice difficulty aligning the bumper or visible corrosion around the mounts.
Installation notes:
Always trial-fit the bumper loosely, align it to the body lines, and then torque fasteners securely. Use proper shims, spacers, and fresh mounting hardware or isolators to achieve perfect fit and long-term stability.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
64450513105
The product you are viewing cross references to these numbers
- Porsche 356 1950-55
- Porsche 356A 1955-59
Kit for both front fog/spot lamps
Fits:
Porsche 356 Pre A - 1950 to 1955
Porsche 356A - 1955 to 1959
Fog lamp mounting kit with hardware. Mounting brackets are made from aluminium
- Porsche 356 1950-55
- Porsche 356A 1955-59
Sold each - 4 required per car
Fits:
Porsche 356 pre A - 1950 to 1955
Porsche 356A - 1955 to 1959
Diagram ref no 5
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
35658168
The product you are viewing cross references to these numbers
OEMatch Support Brackets, Retainers and Braces — Fit, Function, Confidence
OEMatch supplies support brackets, retainers and braces selected for Porsche models to help restore or maintain the correct attachment and alignment of bumpers and related bodywork. These parts cover structural mounts, corner fixing plates and complete hardware kits used in repairs, restorations and routine replacement work.
Available Types
- Front bumper support brackets designed to link the bumper to the chassis and maintain correct position
- Side mounts and fixing plates that secure bumper corners and minimise movement or vibration
- Classic bumper mounts and braces reproduced for vintage Porsche models to preserve original geometry
- Fitting kits and hardware sets including bolts, washers, spacers and clips specified for correct installation
Understanding OEMatch Support Brackets, Retainers and Braces
OEM Original Equipment Manufacturer parts are made by the same company that produced your Porsche’s original support brackets, retainers and braces. OE Original Equipment refers to parts matching original specifications for the support brackets, retainers and braces and may be supplied by alternative manufacturers. Aftermarket parts offer alternative options, sometimes with enhanced features or better value. OEMatch supplies non-OEM support brackets, retainers and braces engineered as direct-fit alternatives to OEM parts, made to original-spec dimensions and tolerances for Porsche models. OEMatch provides a wide selection of parts for Porsche applications and has catalogued thousands of part references to support repairs across different model years. Typical support brackets transfer load between bumper and structure, provide mounting datum for trim panels and retain finishing alignment during everyday use or after impact repair.
Benefits Include
- Consistent bumper alignment for correct exterior fit and maintained aerodynamics
- Materials and coatings chosen to resist corrosion and extend service life
- Compatibility with factory mounting points to simplify installation and reduce modification
Why Support Brackets, Retainers and Braces Wear and Fail
- Impact damage from collisions or low speed contact can bend or fracture mounts
- Corrosion and environmental degradation weaken metal over time and compromise fastenings
- Fatigue from repeated loading and vibration loosens fixings or produces cracks
The Importance of Replacing with OEMatch Support Brackets, Retainers and Braces
Replacing defective or distorted support brackets, retainers and braces restores the intended load paths and mounting geometry of the bumper and adjacent panels. Using replacement items specified for Porsche models reduces the risk of misalignment, prevents accelerated wear of adjacent trim and helps ensure that crash energy paths remain as designed. Where original parts are unavailable OEMatch supplies engineered alternatives that reflect original dimensions and tolerances and are selected for fit and function across common Porsche applications.
Advantages
- Direct fit replacements engineered to match original dimensions and tolerances
- Clear mounting points and compatible fixings to aid correct assembly
- Coverage across a wide range of model years to support repairs and restorations
