do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
Bumper Front Seals
By OE Match
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
• Front bumper – OE Match LEFT impact-tube bellows (OE ref no: 91179950513)
• Front bumper – OE Match RIGHT impact-tube bellows (OE ref no: 91179950514)
• Rear bumper – OE Match LEFT impact-tube bellows (OE ref no: 91179950515)
• Rear bumper – OE Match RIGHT impact-tube bellows (OE ref no: 91179950516)
Each bellow is manufactured to replicate the original Porsche specification: correct corrugated profile, rubber compound, precise mounting holes and correct dimensions for the impact-tube housing. These bellows sit between the bumper tube and chassis mount (front and rear) on the 911/930 impact-bumper models (built 1974-1989), sealing and cushioning the energy-absorbing bumper assembly while ensuring the correct aesthetic appearance when the impact tubes are removed or replaced.
Fits:
Porsche 911 1974 - 1989
Porsche 930 1976 - 1989
Diagram ref no 42 (front bumper) and 14 (rear bumper)
Constructed from high-quality rubber with correct hardness and ageing-resistant compound, the bellows restore proper fitment, eliminate flapping or sagging, maintain correct bumper tube alignment and preserve that factory-correct look of the early “G-series” 911 / 930 models.
• Function: These bellows serve to cushion and seal the bumper impact tubes, protect the chassis mount region from road debris and water ingress, provide correct mounting geometry and restore the original gap/flex behaviour of the bumper system.
While bellows may seem like minor rubber parts they play a crucial role:
• Worn or collapsed bellows can lead to loose or mis-aligned bumper tubes, which may damage paintwork or rubber finish around the mounting.
• Missing or deteriorated bellows allow dirt, water and debris into the impact-tube housing, accelerating corrosion and reduced structural integrity.
• Incorrect or absent seals can lead to visible gaps, poor bumper alignment and reduced impact-absorption performance.
Replacing all four at once ensures symmetrical bumper behaviour, restores correct fitment front and rear, and preserves the value and originality of your G-series 911 or 930.
When to replace:
• Original bellows appear cracked, hardened, sagging or distorted.
• You’re replacing bumper tubes, painting bodywork or restoring the front/rear sections.
• The vehicle is being prepared for show, sale or concours and requires correct rubber components.
• You’re experiencing loose bumper feel, water ingress in the mount region or visible rubber deterioration.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
BUMPERBELLOWSET
The product you are viewing cross references to these numbers
This kit is comprised of the following items:
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 968 3.0L 1992-94
- Porsche 968 Sport 3.0L 1994-95
- Porsche 968 CS 3.0L 1993-95
- Porsche 968 Turbo S 3.0L 1993-94
Fits:
Porsche 911 TURBO 1977-89
Contains:
2x 93050319700 Rear 1/4 Panel to Body Seal
2x 91150332500 Front Bumper Bottom Seal
2x 91150332600 Front Bumper Upper Seal
2x 90150339422 Front Windscreen Scuttle Seal
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
PCG50339400
The product you are viewing cross references to these numbers
This kit is comprised of the following items:
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
This bellow fits where the bumper's impact-absorbing tube meets the chassis mount. It replicates the original Porsche's form and function: the correct corrugated rubber profile, factory-style mounting holes, accurate dimensions, and the correct spacing between mounting tabs.
Porsche 911 1974 - 1989
Diagram ref no 42
• Position: Front bumper, left/right side impact-tube bellow (part number 91179950513/ 91179950514) – between bumper tube and chassis mount bracket.
• Function: Provides sealed flexible coupling between front bumper impact tube and chassis mount, absorbs minor movement/shock, prevents debris ingress, maintains correct bumper mounting geometry and fitment.
• Material & Construction: Corrugated rubber bellow manufactured to exact original Porsche profile, with correct mounting flange and bolt-hole spacing, designed for direct-fit replacement.
• Applications: Ideal when the original bellow is cracked, collapsed, missing, sagging, or has deteriorated rubber and no longer provides correct sealing or alignment.
Although often overlooked, the impact-bumper bellows play an important role in the structural and visual integrity of the bumper system. If the bellows are missing or worn, you may face:
• Rearranged or sagging bumper tube alignment
• Water or road-salt ingress into mounting areas, promoting corrosion
• Noticeable gaps or mis-alignment at bumper ends, affecting appearance
• Excess vibration or looser bumper feel due to degraded rubber
Replacing the bellow restores correct mounting geometry, prevents damage to the chassis or bumper tube, restores the original look and seals out elements.
When to replace:
• The rubber is cracked, faded, sagged or missing
• The bumper tube shows signs of corrosion or mis-alignment at the joint
• During bodywork, restoration, bumper tube replacement, or mount servicing
• You want to ensure authentic trim and correct condition for your classic Porsche
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
9117995051
The product you are viewing cross references to these numbers
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Porsche 911 1974-89
Diagram Ref no 42
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
9117995051
The product you are viewing cross references to these numbers
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
DAMAGED Front Smile Rubber.
This is a damaged in transit part and has a visible crack, offered for parts or refurbishment purposes only. Ideal for restoration specialists, collectors, or workshops looking for components at reduced cost.
NOTE: For spares, repair, or core replacement only.
Condition:
This Front Smile Rubber is brand new and never been fitted. It has some transport damage which is repairable.
Please see the gallery of images before purchasing.
Fits:
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91150518705
The product you are viewing cross references to these numbers
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
High quality OE Match replacement bumper guards, designed to replicate the original factory rubber corners of classic Porsche 911 models, providing proper protection and a look consistent with the original design.
Fits:
Porsche 911 1974 - 1989
Diagram ref no 24
Installed at each front bumper corner, this rubber trim fills the gap between the bumper and bodywork, helping protect painted surfaces from minor impacts, stone chips, and abrasion. Over years of use, original bumper rubbers can become hard, cracked, faded, or missing altogether - detracting from the classic lines of the 911’s front end and reducing protective coverage. This OE Match alternative offers correct fit and texture for restoration, maintenance, or exterior refresh projects.
The front bumper corner rubber provides protective padding and contouring at the outer edges of the front bumper. It helps absorb minor impacts, prevents direct contact between bumper and bodywork, and completes the classic exterior appearance.
Function:
• Protects front bumper edges and adjacent bodywork from minor impact damage
• Fills and finishes bumper corner gap with correct contour
• Restores OEM-style look and alignment
• Durable, weather-resistant rubber compound for long service life
Old or deteriorated bumper corner rubbers can harden, crack, or fall off, leaving the bumper edge and bodywork exposed to wear, chips, or impact damage. Replacing them with correct OE Match rubbers restores proper protective coverage, improves the classic front end look, and helps maintain the integrity of original body trim.
When to replace:
• Visible cracking, splitting, or hardening of the rubber
• Faded or discoloured corners
• Rubbers missing or loosely fitted
• After impact damage to bumper corners
• During front bumper restoration or detailing
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91150530
The product you are viewing cross references to these numbers
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Fits:
Porsche 911 Converted to wide body RSR / ST
or back dated to wide body RSR / ST look
Diagram ref no 18.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
90150509120RSR
The product you are viewing cross references to these numbers
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
The OE MATCH Front Smile Rubber is a high-quality replacement body trim seal designed to fit along the top edge of the front bumper on classic Porsche models. Commonly referred to as the "smile" rubber due to its distinctive curved shape, this component fills the gap between the front bumper and bodywork, providing a clean, factory-correct appearance while helping to protect the area from dirt, moisture, and road debris.
Fits:
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Manufactured to OE specifications, the smile rubber offers precise fitment, flexibility, and durability. It is an essential component for restoration projects or replacing aged, cracked, or distorted original seals, helping to restore the vehicle's original appearance and finish.
What This Product Does:
- Seals the gap between the front bumper and bodywork
- Provides a clean, factory-original appearance
- Helps prevent dirt, water, and debris from collecting behind the bumper
- Improves the visual finish of the vehicle's front end
- Reduces unwanted gaps between body panels and trim
- Supports accurate restoration of classic Porsche models
Symptoms Of Wear Or Failure:
- Cracked, split, or perished rubber
- Warping, shrinking, or distortion of the seal
- Loose or detached sections
- Fading, hardening, or loss of flexibility
- Visible gaps between the bumper and bodywork
- Water or debris accumulation behind the bumper
- Poor panel appearance and alignment
- Aged or deteriorated exterior trim appearance
Why Replacement Matters:
- Restores the original factory appearance of the front bumper area
- Provides a neat and uniform body-to-bumper transition
- Helps prevent dirt and moisture ingress behind the bumper
- Improves overall vehicle presentation and value
- Supports concours-quality restorations and refurbishment projects
- Maintains proper fitment and trim alignment
- Prevents further deterioration of surrounding trim areas
- Provides long-lasting durability and OE-quality fit and finish
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91150518705
The product you are viewing cross references to these numbers
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Fits:
Porsche 911 (930) Turbo 1975-89
Diagram Ref: 32
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93050305502
The product you are viewing cross references to these numbers
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
OE Match front bumper intake for oil-cooler airflow on Porsche 911 and 930 Turbo models from 1974–1989. It provides an air entry point towards the front-mounted oil cooler on the G-model 911.
Fits
Porsche 911 - 1974 to 1989
- 911 1974–1977 2.7L / 1976–77 3.0 Carrera
- 911 1978–1983 3.0L / SC
- 911 1984–1986 3.2L
- 911 1987–1989 3.2L G50
- 911 1975–1977 3.0L Turbo (930)
- 911 1978–1989 3.3L Turbo (930)
Check fitment for your specific vehicle (model, year, engine) before ordering.
Diagram ref no 13
What This Product Does
This intake directs incoming air from the bumper area towards the oil cooler. Its purpose concerns the cooler's air supply; it is not an oil-carrying component or a replacement cooler.
Functions
- Provides an inlet for cooling air at the front bumper.
- Guides incoming airflow towards the oil cooler.
- Forms part of the exterior oil-cooling airflow arrangement.
Technical Details
- Brand: OE Match.
- Application: Porsche 911 G-model, including the listed 930 Turbo variants.
- Installation area: front bumper.
- Associated internal diagram reference: 91150530800, described as a cover.
Symptoms of Fault
Inspect the intake if it has visible cracks, damaged attachment points, looseness or an obstructed opening. Rattling or contact marks around adjacent bodywork can also warrant checking the fit and fixings. These signs should be assessed before deciding which component needs replacement.
Why Replacement Matters
Renewing a damaged or missing intake restores the intended air-entry arrangement. Check the surrounding ducting and attachments at the same time, since an obstruction or loose adjoining component will not be addressed by replacing the intake alone.
FAQs
Is this the oil cooler itself?
No. This component is an air intake positioned at the bumper, rather than the heat exchanger.
What should be checked before fitting?
Confirm the vehicle application, bumper configuration and existing cooler arrangement. Compare the mounting area and inspect associated fixings before any painting or modification.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91150530800
The product you are viewing cross references to these numbers
OEMatch Bumper Front Seals — Fit, Function, Confidence
Front bumper seals for Porsche models close gaps between the bumper, adjacent panels and lighting to limit water ingress and debris while maintaining panel alignment and reducing vibration and wind noise. OEMatch parts are chosen to suit restoration, collision repair and routine maintenance of Porsche vehicles.
Available Types
- EPDM profile seals for exterior edges
- Neoprene compression seals for tight joints
- Foam-filled edge seals for paint protection
Understanding OEMatch Bumper Front Seals
OEM (Original Equipment Manufacturer) parts are made by the same company that produced your Porsche’s original bumper front seals.
OE (Original Equipment) refers to parts matching original specifications for the bumper front seals and may be supplied by alternative manufacturers. Aftermarket parts offer alternative options, sometimes with enhanced features or better value. OEMatch supplies non-OEM bumper front seals engineered as direct-fit alternatives to OEM parts, made to original-spec dimensions and tolerances for Porsche models.
OEMatch supplies a wide selection of items for Porsche applications including gaskets, suspension hardware, engine parts and interior trim, supported by a large catalogue of part numbers and cross-references to original specifications. Products are offered for both classic and modern Porsche models to assist restoration and repair projects.
Benefits Include
- Prevents moisture ingress that can lead to corrosion
- Reduces vibration and rattles for improved refinement
- Preserves panel alignment and exterior appearance
- Protects paintwork at contact edges during refit
Why Bumper Front Seals Wear and Fail
- UV exposure causes hardening, cracking or shrinkage
- Heat and ozone accelerate material degradation
- Compression fatigue from repeated movement and vibration
- Chemical contamination such as oils or cleaning agents
The Importance of Replacing with OEMatch Bumper Front Seals
Replacing worn or damaged front bumper seals restores proper sealing, prevents water reaching vulnerable areas and keeps panel gaps consistent with factory alignment. Renewing seals during restoration or repair helps avoid corrosion, reduces noise and protects adjacent paint and trim, contributing to long-term preservation of Porsche bodywork and lighting assemblies.
Advantages
- Direct-fit replacements engineered to match original dimensions and tolerances
- Materials chosen for flexibility, UV and heat resistance
- Options suitable for restoration, repair and detailing projects
Support & Advice
Fitting can appear straightforward but may require specific procedures such as correct positioning, sealing detail and careful reassembly to avoid panel damage. If you lack the right tools or experience, or if the vehicle includes hidden fasteners or sensors, seek professional installation. Recheck fasteners and seal compression after initial use.
