do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
Pin Kit and Guide Plates
By OE Match
- Porsche 356 1950-55
- Porsche 356A 1955-59
- Porsche 356B 1959-63
OE Match supplies this handbrake hardware kit for Porsche 356, 356A and 356B drum brake assemblies. It provides replacement shoe-fitting hardware for maintenance and restoration work.
Fits
Porsche 356 - 1950 to 1955
Porsche 356A - 1955 to 1959
Porsche 356B - 1959 to 1963
Fits both front and rear drum brakes
1 set per car
Check fitment for your specific vehicle (model, year, engine) before ordering.
What This Product Does
This kit concerns the fittings associated with the brake shoes, rather than their friction linings. The supplied assembly references identify tension springs, roll pins, compression springs and concave washers used around the shoes.
Functions
- Provides replacement hardware for drum brake shoe servicing.
- Supports shoe retention and spring action within the brake assembly.
- Allows deteriorated fittings to be renewed during restoration.
Technical Details
- 35642168: tension spring; diagram quantity 6.
- 35642169: roll pin; diagram quantity 8.
- 35642172: tension spring; diagram quantity 4.
- PCG64442208: compression spring; diagram quantities 8 or 4 according to assembly. The early brake diagram includes applications marked 356 and 356 A/540.1.
- 251609289: concave washer; diagram quantities 8 or 4 according to assembly.
- These quantities describe the referenced assemblies and are not a confirmed packing list for the kit.
Symptoms of Fault
Inspect existing fittings for corrosion, distortion, seizure or looseness. Rattling and brake noise warrant examination of the hardware alongside the shoes and surrounding components; these symptoms alone do not establish which part needs replacement.
Why Replacement Matters
Renewing damaged fittings avoids reinstalling deteriorated hardware during brake work. OE Match develops replacement components around Porsche applications, with attention to original references and vehicle-specific fitment. Check the condition of adjoining parts rather than assuming a hardware kit will resolve every braking fault.
FAQs
How many sets are specified for a vehicle?
The supplied requirement is one set per car.
Is this only for the rear brakes?
No. The stated application covers drum brakes at both ends of the vehicle.
Do the diagram quantities confirm the kit contents?
No. They identify assembly requirements. Confirm the supplied components against the planned repair before dismantling.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
35642168
The product you are viewing cross references to these numbers
OEMatch Pin Kit and Guide Plates — Fit, Function, Confidence
Pin kits and guide plates are small but critical parts of a Porsche's braking system, keeping pads aligned and allowing controlled movement within the caliper. OEMatch offers a focused selection for Porsche applications, suitable for routine service, caliper rebuilds and restoration where hardware renewal is needed.
Available Types- Standard pin kits for routine servicing
- Stainless steel kits to reduce corrosion
- Guide plates and shims for pad alignment and fit
OEM (Original Equipment Manufacturer) parts are made by the same company that produced your Porsche's original pin kit and guide plates. OE (Original Equipment) refers to parts matching original specifications for the pin kit and guide plates and may be supplied by alternative manufacturers. Aftermarket parts offer alternative options, sometimes with enhanced features or better value. OEMatch supplies non-OEM pin kit and guide plates engineered as direct-fit alternatives to OEM parts, made to original-spec dimensions and tolerances for Porsche models.
Pin kits and guide plates allow pads to move correctly within the caliper housing, maintaining even contact with the disc and reducing vibration that causes noise. Over time pins and plates can corrode, seize or deform; renewal during a caliper service helps restore consistent pad movement and even wear.
Benefits Include- Restores smooth, controlled pad movement
- Helps prevent uneven pad wear and brake noise
- Supports consistent brake action and component life
- Corrosion from moisture or road salt
- Wear from repeated pad movement and friction
- Contamination from brake dust and debris leading to binding
Replacing worn or corroded pin kits and guide plates reinstates reliable pad alignment and prevents secondary damage to pads and discs. Using correctly dimensioned hardware reduces the risk of sticking or uneven wear and contributes to predictable brake feel after service or rebuild.
Advantages- Made to original-spec dimensions and tolerances for Porsche models
- Manufactured from corrosion-resistant materials where specified
- Supplies intended for service, restoration and rebuild tasks
These items affect safety-critical systems. Installation should be carried out by a qualified technician following model-specific procedures and torque settings. Use calibrated tools and new fasteners where specified.
