Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 914 (1970-1976)
The OE Match Engine Cylinder Head Exhaust Valve is a precision replacement valvetrain component for the Porsche 914-4 1.7L air-cooled engine.
Fits:- Porsche 914-4 1.7L
Diagram Ref No 17
Located in the cylinder head, the exhaust valve controls the release of burnt combustion gases from the cylinder. During the exhaust stroke, it opens to allow gases to pass into the exhaust system before closing securely against the valve seat for the next engine cycle.
Because exhaust valves operate directly in the path of extremely hot combustion gases, they experience significant thermal and mechanical stress. Correct valve condition, alignment and seating are essential for maintaining cylinder compression, efficient combustion and reliable engine performance.
What This Product Does:
- Controls the release of burnt gases from the combustion chamber.
- Opens during the exhaust stroke to allow gases to leave the cylinder.
- Closes against the valve seat to seal the combustion chamber.
- Helps maintain correct cylinder compression.
- Supports efficient engine breathing and combustion.
- Helps maintain smooth and consistent engine performance.
- Transfers heat from the valve into the valve seat and cylinder head when closed.
- Works with the valve guide, valve seat, spring and associated valvetrain components.
- Replaces a burnt, bent, pitted or excessively worn exhaust valve.
- Helps restore correct cylinder-head operation during an engine rebuild.
The valve must move freely within its guide and contact the valve seat evenly around its circumference. Wear or damage that prevents complete seating can allow compression and hot gases to escape.
Symptoms Of Wear Or Failure:
Possible symptoms include:
- Low or uneven cylinder compression.
- Engine misfires.
- Rough or unstable idle.
- Loss of engine power.
- Poor acceleration.
- Difficult starting.
- Increased fuel consumption.
- Irregular exhaust note.
- Ticking or tapping noises from the valvetrain.
- Poor compression-test results.
- Leakage through the exhaust during a cylinder leak-down test.
- Burnt or pitted valve face.
- Erosion around the seating surface.
- Bent or damaged valve stem.
- Excessive valve-stem wear.
- Heavy carbon deposits.
- Failure of the valve to seal correctly against its seat.
A leaking exhaust valve allows combustion pressure to escape into the exhaust port rather than remaining within the cylinder, reducing compression and engine efficiency.
Why Replacement Matters:
Exhaust valves operate under some of the highest temperatures found inside an air-cooled engine.
Every combustion cycle exposes the valve head and seating surface to hot gases while the valve repeatedly opens and closes at high speed. Over time, the valve may suffer from:
- Valve-face erosion.
- Burning or pitting.
- Carbon accumulation.
- Valve-stem wear.
- Mechanical distortion.
- Heat-related material deterioration.
- Wear caused by excessive valve-guide clearance.
- Damage caused by poor valve seating.
Once the valve can no longer seal correctly, cylinder compression can fall and engine performance can deteriorate.
Replacing a worn or damaged exhaust valve helps restore:
- Correct combustion-chamber sealing.
- Cylinder compression.
- Smooth engine operation.
- Consistent power delivery.
- Efficient exhaust flow.
- Correct valvetrain operation.
- Reliable cylinder-head performance.
When Replacement Should Be Considered:
Replacement may be necessary when:
- The valve face is burnt or badly eroded.
- The seating surface is heavily pitted.
- The valve stem is bent.
- Valve-stem wear exceeds specification.
- Compression is significantly reduced in the affected cylinder.
- Leak-down testing confirms leakage through the exhaust valve.
- The valve has suffered overheating.
- Excessive valve-guide clearance has damaged the valve.
- Cylinder-head inspection determines that the valve cannot be safely reused.
- A cylinder-head or complete engine rebuild is being carried out.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
022109612D
The product you are viewing cross references to these numbers