do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 964 (911) TURBO 3.3L 1991-93
- Porsche 964 (911) TURBO 3.6L 1991-93
- Porsche 924 2.0L 1980-85
Size: 22mm diameter
Sold each.
It’s fitted on the rear anti-roll (sway) bar to support and cushion the bar’s mounting points. The stabilizer bar helps reduce body roll (lean) during cornering by transferring forces between the left and right sides of the suspension. The bushing’s job is to hold the bar in place while allowing it to move slightly and absorb vibration.
Fits:
Porsche 924 1978 REAR AXLE
Porsche 964 Turbo (965) REAR AXLE
Diagram ref no 17.
Replacing worn or damaged sway bar bushings is crucial because:
• Ride comfort & handling suffer when bushings are worn—they get sloppy, allowing excessive play in the bar mount, which can lead to clunks, noise, or decreased steering precision
• Safety: A loose stabilizer bar means uneven handling, especially during sharp turns or emergency manoeuvres. Your car may feel “floaty” or unstable
• Prevent further damage: Neglected worn bushings can allow metal-on-metal contact, damaging the stabilizer bar itself, mounting brackets, or adjacent chassis components.
Signs that the PCG411313E bushing may be failing include:
• A clunking or knocking noise from the rear of the car over bumps or during turns.
• Squeaking or creaking sounds from the rear when going over irregular surfaces
• Noticeable body roll / lean during cornering (worse than it used to be
• Uneven tyre wear due to altered suspension geometry
• Visual inspection shows cracks, splitting, flat spots, or hardened rubber, or the bush is missing or loose.
If the stabilizer bar bushing fails and isn’t replaced, the bar can loosen and cause excessive movement, leading to clunks, knocks, and poor handling in corners. This not only reduces driving confidence and safety but can also overload other suspension parts, creating bigger problems and costly repairs over time.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
PCG411313E
The product you are viewing cross references to these numbers
- Porsche 924 2.0L 1980-85
- Porsche 924 Turbo 2.0L 1982-84
- Porsche 924 Carrera GTS 2.0L 1982
- Porsche 924S 2.5L 1986-87
- Porsche 924S 2.5L 1988
- Porsche 944 2.5L 8V 1982-87
- Porsche 944 2.7L 8V 1988-89
- Porsche 944S 2.5L 16V 1987-88
- Porsche 944S2 3.0L 16V 1989-91
- Porsche 944 Turbo 2.5L 8V 1985-88
- Porsche 944 Turbo 2.5L 8V 1989-91
- Porsche 944 Turbo S 2.5L 8V 1988
- Porsche 968 3.0L 1992-94
- Porsche 968 Sport 3.0L 1994-95
- Porsche 968 CS 3.0L 1993-95
- Porsche 968 Turbo S 3.0L 1993-94
Fits:
Porsche 924 / 924S - 1982-88
Porsche 944 - 1982-91
Porsche 944 S2 1989-91
Porsche 968 1992-95
Diagram Ref No 2
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
94434373332
The product you are viewing cross references to these numbers