Please wait… 
Please wait while we process your order,
do not press the back button…
do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
Rear bumper top seal. Porsche 911 1974-89 - 91150308505
91150308505/8
Vehicle Group
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Information
Rear bumper top seal.
Rear bumper to body rubber seal - installed under the bumper edge to seal the joint between the bumper and bodywork.
Fits:
Porsche 911 1974 - 1989
Diagram ref no 34
The rear bumper seal creates a weatherproof barrier between the bumper and the body panel. It prevents water, road debris, dust, and contaminants from penetrating the space where the bumper meets the vehicle structure. In addition to protection, it helps maintain a tight, factory-correct joiner surface that reduces wind noise and vibration.
Over time, original bumper seals can harden, shrink, crack, or split from heat, aging, and exposure to road conditions. When worn, seals can allow:
• Moisture ingress leading to corrosion
• Wind and road noise
• Dirt intrusion under body panels
• Visible gaps or uneven bumper fitment
Replacing a worn/recovering seal restores the correct factory sealing and finish - maintaining the visual integrity and long-term protection of your classic Porsche.
Replace this rear bumper seal if you notice:
• Cracks, splits, or missing rubber
• Loose or uneven bumper alignment
• Water entry or dampness near the rear panel
• Excessive wind noise while driving
• During bumper removal or restoration work
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91150308505
The product you are viewing cross references to these numbers
Rear bumper to body rubber seal - installed under the bumper edge to seal the joint between the bumper and bodywork.
Fits:
Porsche 911 1974 - 1989
Diagram ref no 34
The rear bumper seal creates a weatherproof barrier between the bumper and the body panel. It prevents water, road debris, dust, and contaminants from penetrating the space where the bumper meets the vehicle structure. In addition to protection, it helps maintain a tight, factory-correct joiner surface that reduces wind noise and vibration.
Over time, original bumper seals can harden, shrink, crack, or split from heat, aging, and exposure to road conditions. When worn, seals can allow:
• Moisture ingress leading to corrosion
• Wind and road noise
• Dirt intrusion under body panels
• Visible gaps or uneven bumper fitment
Replacing a worn/recovering seal restores the correct factory sealing and finish - maintaining the visual integrity and long-term protection of your classic Porsche.
Replace this rear bumper seal if you notice:
• Cracks, splits, or missing rubber
• Loose or uneven bumper alignment
• Water entry or dampness near the rear panel
• Excessive wind noise while driving
• During bumper removal or restoration work
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91150308505
91150308505
The product you are viewing cross references to these numbers
Price: €49.14
In stock