Please wait… 
Please wait while we process your order,
do not press the back button…
do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
Main shaft seal. Porsche 911/912 1972-86 - 99911332740
99911332740/1
Vehicle Group
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
Information
Main shaft seal,
23 x 35 x 8/11.
A rubber shaft oil seal (radial seal) for the main/input shaft of a 901/915-series gearbox. It fits around the rotating shaft and seals the interface between the rotating shaft and the gearbox housing to prevent gearbox oil leaks.
Dimensions: 23 mm (shaft diameter) × 35 mm (outer diameter) × 8/11 mm thickness (seal housing/dual-lip design).
Fits:
Porsche 911 1972 - 1973 (TYP 915) from:
G 733 7575 >>
G 723 0507 >>
G 783 0838 >>
Porsche 911 Carrera 1973 - 1986
Diagram ref no 11
This seal prevents gearbox oil from escaping around the input or main shaft, ensuring the transmission remains properly lubricated. It also blocks dirt, water, and other contaminants from entering the gearbox, helping preserve internal components and maintain correct operating pressure. By replacing a worn, hardened, or cracked original seal, it restores a clean, leak-tight barrier for reliable long-term gearbox performance.
Original gearbox seals degrade over time: rubber lips harden or crack, springs lose tension, and sealing surfaces wear. A failing main-shaft seal typically leads to:
• Gearbox oil leaks
• Loss of gearbox oil over time (low oil level)
• Contamination ingress (dirt, water), leading to accelerated gearbox wear or internal damage
• Messy drip underneath the car and gearbox housing
Replacing the seal with a correct-spec new unit restores proper sealing, preserves gearbox oil integrity, and helps prevent costly internal damage or gearbox failure.
You should replace this seal if:
• Gearbox oil leaks are visible around the input shaft or bellhousing area
• There is seepage, oil dripping, or a film of oil on the underside of gearbox or clutch area
• The old seal appears cracked, hardened, or visibly damaged
• You are doing a gearbox rebuild, overhaul or maintenance
• You notice loss of gearbox oil or suspect contamination ingress
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99911332740
The product you are viewing cross references to these numbers
A rubber shaft oil seal (radial seal) for the main/input shaft of a 901/915-series gearbox. It fits around the rotating shaft and seals the interface between the rotating shaft and the gearbox housing to prevent gearbox oil leaks.
Dimensions: 23 mm (shaft diameter) × 35 mm (outer diameter) × 8/11 mm thickness (seal housing/dual-lip design).
Fits:
Porsche 911 1972 - 1973 (TYP 915) from:
G 733 7575 >>
G 723 0507 >>
G 783 0838 >>
Porsche 911 Carrera 1973 - 1986
Diagram ref no 11
This seal prevents gearbox oil from escaping around the input or main shaft, ensuring the transmission remains properly lubricated. It also blocks dirt, water, and other contaminants from entering the gearbox, helping preserve internal components and maintain correct operating pressure. By replacing a worn, hardened, or cracked original seal, it restores a clean, leak-tight barrier for reliable long-term gearbox performance.
Original gearbox seals degrade over time: rubber lips harden or crack, springs lose tension, and sealing surfaces wear. A failing main-shaft seal typically leads to:
• Gearbox oil leaks
• Loss of gearbox oil over time (low oil level)
• Contamination ingress (dirt, water), leading to accelerated gearbox wear or internal damage
• Messy drip underneath the car and gearbox housing
Replacing the seal with a correct-spec new unit restores proper sealing, preserves gearbox oil integrity, and helps prevent costly internal damage or gearbox failure.
You should replace this seal if:
• Gearbox oil leaks are visible around the input shaft or bellhousing area
• There is seepage, oil dripping, or a film of oil on the underside of gearbox or clutch area
• The old seal appears cracked, hardened, or visibly damaged
• You are doing a gearbox rebuild, overhaul or maintenance
• You notice loss of gearbox oil or suspect contamination ingress
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99911332740
99911332740
91530238100
99911328340
The product you are viewing cross references to these numbers
Price: €10.53
In stock