do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
.jpg?width=440&height=320 "Crankshaft Position Sensor, Cylinder 6-10. Porsche 918 Carrera GT - 98060611300, 98060611301 - 114545")
.jpg){kind=link}
.jpg){kind=link}
- Porsche Carrera GT 2003-06
Restore accurate engine speed and crankshaft position monitoring with this OE Match Crankshaft Position Sensor, specified for the cylinders 6–10 application on compatible Porsche engines.
Fits:- Porsche Carrera GT 2003-06
Diagram Ref No 40
The crankshaft position sensor is a critical engine-management component. It monitors the rotational position and speed of the crankshaft and sends this information to the engine control unit (ECU). The ECU uses this signal to coordinate essential functions such as ignition timing and fuel injection.
Accurate crankshaft position information allows the engine management system to determine precisely where the engine is within its operating cycle. If the sensor signal becomes weak, intermittent or disappears completely, the ECU may be unable to control ignition and injection correctly. This can lead to difficult starting, misfires, poor running or a complete no-start condition.
Electrical sensors can deteriorate through age, repeated heat cycles, vibration, damaged wiring or connector problems. Some failures can also be temperature-related, with the sensor working correctly when cold but becoming unreliable once the engine reaches operating temperature.
This OE Match Crankshaft Position Sensor provides a high-quality replacement for a faulty or damaged sensor, helping restore accurate engine timing information and dependable engine-management operation.
What This Product Does:
- Monitors crankshaft rotational position.
- Measures crankshaft speed or engine RPM.
- Sends crankshaft position information to the ECU.
- Helps the ECU determine correct engine timing.
- Supports accurate ignition control.
- Supports correctly timed fuel injection.
- Helps maintain smooth and consistent engine operation.
- Provides essential information during engine starting.
- Supports accurate engine-management diagnostics.
- Helps maintain reliable performance across changing engine speeds and loads.
- Replaces an intermittent, damaged or failed sensor.
- Is specified for the applicable cylinders 6–10 position/application.
- Engine cranks but does not start.
- Intermittent starting problems.
- Extended cranking before the engine starts.
- Engine unexpectedly cutting out.
- Engine stalling when hot.
- Engine restarting after it has cooled down.
- Intermittent loss of engine power.
- Rough or inconsistent engine operation.
- Engine misfires.
- Hesitation during acceleration.
- Check engine or engine-management warning light.
- Crankshaft position sensor-related diagnostic fault codes.
- Engine speed signal disappearing during diagnostic testing.
- Tachometer or RPM information behaving abnormally where applicable.
- Damaged sensor wiring or electrical connector.
- Heat-related intermittent sensor failure.
Why Replacement Matters:
- A sensor that fails completely can potentially prevent the engine from starting. An intermittent sensor can be more difficult to diagnose because the vehicle may operate normally before suddenly stalling or refusing to restart.
- Heat-related deterioration is particularly troublesome. A failing sensor may work when the engine is cold but lose its signal as temperatures rise, potentially causing the engine to cut out during operation.
- An inaccurate or unstable signal can also contribute to misfires, poor performance and engine-management warning lights.
- Because crankshaft position information is directly related to ignition and injection control, unresolved sensor faults can compromise overall engine reliability and may leave the vehicle unable to start.
- Replacing a defective component with this OE Match Crankshaft Position Sensor helps restore accurate engine speed and position information, dependable starting and correct engine-management operation.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
98060611301
The product you are viewing cross references to these numbers