do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 955 Cayenne 3.2L V6 2003-06
- Porsche 955 Cayenne S 4.5L V8 2003-06
- Porsche 955 Cayenne Turbo 4.5L 2003-06
- Porsche 955 Cayenne Turbo S 4.5L 2006>>
OE Match eccentric suspension bolt M14x1.5x105 for Porsche 955 Cayenne models. This replacement alignment bolt is used in the suspension system to help secure and adjust suspension geometry correctly.
Sold each, Fits front and rear suspension
Fits:
Porsche 955 Cayenne 2003 - 2006
Diagram ref no 5
The eccentric suspension bolt secures the relevant suspension arm or mounting point while allowing alignment adjustment. Correctly fitted eccentric bolts are important for camber, toe, wheel alignment stability, tyre wear, and overall suspension performance.
Functions
• Replaces the eccentric suspension adjustment bolt
• Secures the relevant suspension arm or mounting point
• Supports suspension alignment adjustment
• Helps maintain correct wheel geometry
• Assists with camber or toe setting where applicable
• Replaces corroded, seized, stretched, worn, or damaged original bolts
• OE Match replacement fixing for Porsche Cayenne suspension service.
Why Replace This Part?
Eccentric suspension bolts are exposed to road dirt, moisture, corrosion, suspension load, and repeated alignment work. Over time, they can seize, corrode, stretch, round off, or become difficult to adjust. A worn or damaged eccentric bolt may prevent accurate wheel alignment and can affect handling, tyre wear, and suspension setup. Replacement is recommended during suspension arm, bush, or alignment service when the original bolt is damaged or seized.
When to Replace This Part
• Suspension alignment cannot be adjusted correctly
• The original eccentric bolt is seized, corroded, rounded, stretched, or damaged
• Suspension arms or bushes are being replaced
• Camber or toe adjustment is being carried out
• Uneven tyre wear or poor wheel alignment is being investigated
• The bolt has been removed during suspension repair
• The vehicle is undergoing Porsche Cayenne suspension restoration.
Where it fits on the car
This bolt fits within the suspension alignment and mounting system on Porsche 955 Cayenne models. Exact position can vary depending on axle location and suspension arm layout.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
PAF001833
The product you are viewing cross references to these numbers
- Porsche 944 2.5L 8V 1982-87
Front Lower Wishbone
Restore the precision handling and balanced driving dynamics
of your Porsche 944 with this OE Match Front Lower Wishbone, suitable for
Porsche 944 models produced between 1984 and 1986. This critical suspension component helps
maintain correct wheel alignment, steering response and suspension geometry,
ensuring the vehicle performs as Porsche intended.
Fits:
- Porsche 944 2.5L 8V 1982-86
Diagram ref no 2
Manufactured to OE specifications, this replacement lower wishbone provides the correct fit, strength and durability required for both everyday driving and enthusiastic road use. Whether you're rebuilding the front suspension, correcting handling issues or carrying out a full restoration, replacing worn suspension components is essential for maintaining safety and performance.
What Does the Front Lower Wishbone Do?
The front lower wishbone, also known as a control arm, forms a key part of the Porsche 944 front suspension system. It connects the wheel hub assembly to the chassis and controls the movement of the front wheels as the suspension travels over varying road surfaces.
Working together with the suspension bushes, ball joints,
dampers and steering components, the lower wishbone helps:
- Maintain accurate suspension geometry.
- Keep the wheels correctly aligned.
- Improve steering precision and driver feedback.
- Support vehicle stability during braking and cornering.
- Control suspension movement and wheel travel.
- Deliver predictable handling characteristics.
The Porsche 944 is renowned for its balanced chassis and precise handling, making properly functioning suspension arms vital to preserving the driving experience.
Why Do Front Lower Wishbones Fail?
Although the wishbone itself is designed to be durable, years of use, road impacts and environmental exposure can eventually lead to wear or damage.
Common causes of failure include:
- Corrosion caused by moisture and road contaminants.
- Damage from potholes, kerb strikes or road debris.
- Metal fatigue after decades of suspension loading.
- Distortion following accidents or heavy impacts.
- Wear around mounting points and bush housings.
- Excessive stress caused by worn suspension bushes or ball joints.
As Porsche 944 models continue to age, many original suspension components may have experienced decades of service and can benefit from replacement during restoration or maintenance work.
When Should a Front Lower Wishbone Be Replaced?
The front lower wishbone should be inspected whenever suspension work is performed. Replacement may be necessary if you experience:
Excessive play in the suspension. Clunking or knocking noises from the front end. Uneven tyre wear. Poor steering response. Vehicle wandering or pulling under braking. Alignment issues that cannot be corrected. Visible corrosion, cracking or physical damage. During a complete front suspension overhaul.Replacing worn suspension arms helps restore factory handling characteristics, improve steering accuracy and enhance overall driving confidence.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95134102
The product you are viewing cross references to these numbers
- Porsche 944 2.5L 8V 1982-87
- Porsche 944 2.7L 8V 1988-89
- Porsche 944S 2.5L 16V 1987-88
- Porsche 944S2 3.0L 16V 1989-91
- Porsche 944 Turbo 2.5L 8V 1985-88
- Porsche 944 Turbo 2.5L 8V 1989-91
- Porsche 944 Turbo S 2.5L 8V 1988
The OE Match Wishbone Front Bush, Fits in the Rear, is a high-quality replacement suspension bushing designed to provide a secure yet flexible connection between the wishbone (control arm) and the vehicle chassis. Manufactured to OE specifications for fit, durability and performance, this bonded rubber bush helps absorb road shocks, reduce vibration and maintain precise suspension geometry.
Sold Each.
x2 Required Per Car.
Fits:
- Porsche 944 2.5L 8V 1982-87
- Porsche 944 2.7L 8V 1988-89
- Porsche 944S 2.5L 16V 1987-88
- Porsche 944S2 3.0L 16V 1989-91
- Porsche 944 Turbo 2.5L 8V 1985-88
- Porsche 944 Turbo 2.5L 8V 1989-91
- Porsche 944 Turbo S 2.5L 8V 1988
Installed in the rear mounting position of the wishbone, this bush plays a critical role in controlling suspension movement while allowing the necessary articulation of the control arm during driving. Constructed from high-quality rubber and metal components, it is engineered to withstand continuous suspension loads, road impacts and environmental exposure while maintaining ride comfort and handling precision.
What This Product Does:
- Connects the wishbone (control arm) to the vehicle chassis.
- Allows controlled suspension movement and articulation.
- Absorbs road shocks and vibration.
- Maintains correct suspension geometry and wheel alignment.
- Reduces noise, vibration and harshness (NVH).
- Supports stable braking, steering and cornering performance.
- Helps ensure predictable vehicle handling characteristics.
- Protects surrounding suspension components from excessive stress.
Symptoms Of Wear Or Failure:
- Clunking or knocking noises from the suspension.
- Excessive movement within the control arm assembly.
- Vague or imprecise steering feel.
- Uneven or accelerated tyre wear.
- Poor wheel alignment.
- Vehicle wandering or pulling during driving.
- Reduced stability under braking or cornering.
- Increased vibration transmitted into the cabin.
- Visible cracking, splitting or deterioration of the rubber bush.
- Excessive suspension play detected during inspection.
Why Replacement Matters:
- Suspension bushes are subjected to constant movement, road impacts, vibration, temperature fluctuations and environmental contaminants. Over time, the rubber material can harden, crack, deform or separate from its metal housing, reducing its ability to control suspension movement effectively.
- A worn wishbone bush can allow excessive suspension movement, negatively affecting steering precision, braking stability and tyre wear. If left unresolved, additional strain may be placed on ball joints, control arms, tyres and other suspension components, potentially leading to more extensive repairs.
- Replacing a worn wishbone bush restores proper suspension geometry, improves ride quality and enhances vehicle handling. An OE Match replacement provides factory-style fitment, reliable vibration isolation and long-term durability, helping maintain the comfort, safety and performance characteristics expected from your Porsche.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95134104101
The product you are viewing cross references to these numbers
- Porsche 944 2.5L 8V 1982-87
- Porsche 944 2.7L 8V 1988-89
- Porsche 944S 2.5L 16V 1987-88
- Porsche 944S2 3.0L 16V 1989-91
- Porsche 944 Turbo 2.5L 8V 1985-88
- Porsche 944 Turbo 2.5L 8V 1989-91
- Porsche 944 Turbo S 2.5L 8V 1988
- Porsche 968 3.0L 1992-94
- Porsche 968 Sport 3.0L 1994-95
- Porsche 968 CS 3.0L 1993-95
- Porsche 968 Turbo S 3.0L 1993-94
The big question that most owners have about control arm ball joints is "how do I know when my ball joints need replacing?" Most often you'll hear it said that if the boot is torn or cracked, the control arm needs to be replaced. While this isn't a great indicator, it should raise suspicion as to the condition of the ball joint. Other indicators are knocking sounds in the front suspension or noticeable play in the control arm. The play can be checked by pushing up on the control arm (toward the spindle) near the ball joint. Noticeable play between the control arm and the ball joint indicates that the control arm needs to be replaced.
Fits:
Porsche 944 1985-91
Porsche 968 1992-95
For more information about this product CLICK HERE
Fitting Instructions CLICK HERE
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95134100000
The product you are viewing cross references to these numbers